Linux distributie

Iedereen kan hier terecht met vragen over allerhande open source software die niet in de andere fora past.
Plaats reactie
common sense
Berichten: 656
Lid geworden op: 2 augustus 2006, 13:45
    unknown unknown

Bericht door common sense »

Citroentje schreef:Tuurlijk, nog een boekwerk er bij...
Of als je nog een echt boek zoekt: http://oreilly.com/pub/topic/linux

:D
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

Dat zijn er maar een paar, begin ik met deze, goed?
http://oreilly.com/catalog/9781934356227/

Caine.
Gebruikersavatar
Koen_92
Berichten: 758
Lid geworden op: 17 oktober 2006, 19:28
Locatie: Betuwe
    unknown unknown

Bericht door Koen_92 »

Citroentje schreef:Compiz krijg ik hier niet aan de praat, daar heb ik het ook al op het Ubuntu forum over gehad.
Ik weet niet waarom, maar een enkele keer heeft het gewerkt en na een reboot kon ik alleen weer de basis krijgen. :?
Ok, de printer doen we straks (niet te veel tegelijk).

Om compiz werkend te krijgen moet je eerst 3d-drivers hebben geinstalleerd. Of je dit hebt geinstalleerd kun je controleren door deze twee commando's in je terminal te typen:
glxinfo
glxgears

Wat geven die commando's terug?
Gebruikersavatar
adri
Moderator
Berichten: 11541
Lid geworden op: 5 maart 2005, 14:00
Locatie: Diessen
    unknown unknown

Bericht door adri »

Citroentje, je zult merken dat je -als je al langer Linux gebruikt- dat je steeds meer en vaker de commandline gaat gebruiken. Dat gaat vanzelf, je leert steeds meer commando's en het is -zoals Common Sense al zei zeker geen: "terug naar", maar een fikse stap vooruit.
Desalniettemin wil ik je daar nu nog niet teveel mee lastig vallen. Het eerste jaar dat ik Slackware (!) gebruikte, deed ik dat vrijwel geheel grafisch.
Dat komt echt allemaal nog wel, maak je maar niet ongerust. ;)
Afbeelding
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

Koen_92 schreef:
Citroentje schreef:Compiz krijg ik hier niet aan de praat, daar heb ik het ook al op het Ubuntu forum over gehad.
Ik weet niet waarom, maar een enkele keer heeft het gewerkt en na een reboot kon ik alleen weer de basis krijgen. :?
Ok, de printer doen we straks (niet te veel tegelijk).

Om compiz werkend te krijgen moet je eerst 3d-drivers hebben geinstalleerd. Of je dit hebt geinstalleerd kun je controleren door deze twee commando's in je terminal te typen:
glxinfo
glxgears

Wat geven die commando's terug?
De printer heb ik inmiddels aan de praat, jaja, das niet zomaar wat.

Glxinfo geeft dit:

name of display: :0.0
display: :0 screen: 0
direct rendering: No (If you want to find out why, try setting LIBGL_DEBUG=verbose)
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_visual_info, GLX_EXT_visual_rating,
GLX_EXT_import_context, GLX_EXT_texture_from_pixmap, GLX_OML_swap_method,
GLX_SGI_make_current_read, GLX_SGIS_multisample, GLX_SGIX_hyperpipe,
GLX_SGIX_swap_barrier, GLX_SGIX_fbconfig, GLX_MESA_copy_sub_buffer
client glx vendor string: SGI
client glx version string: 1.4
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_allocate_memory,
GLX_MESA_copy_sub_buffer, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_OML_sync_control,
GLX_SGI_make_current_read, GLX_SGI_swap_control, GLX_SGI_video_sync,
GLX_SGIS_multisample, GLX_SGIX_fbconfig, GLX_SGIX_pbuffer,
GLX_SGIX_visual_select_group, GLX_EXT_texture_from_pixmap
GLX version: 1.2
GLX extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_copy_sub_buffer,
GLX_OML_swap_method, GLX_SGI_make_current_read, GLX_SGIS_multisample,
GLX_SGIX_fbconfig, GLX_EXT_texture_from_pixmap
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.4 (2.1 Mesa 7.0.3-rc2)
OpenGL extensions:
GL_ARB_depth_texture, GL_ARB_draw_buffers, GL_ARB_fragment_program,
GL_ARB_imaging, GL_ARB_multisample, GL_ARB_multitexture,
GL_ARB_occlusion_query, GL_ARB_point_parameters, GL_ARB_point_sprite,
GL_ARB_shadow, GL_ARB_shadow_ambient, GL_ARB_texture_border_clamp,
GL_ARB_texture_compression, GL_ARB_texture_cube_map,
GL_ARB_texture_env_add, GL_ARB_texture_env_combine,
GL_ARB_texture_env_crossbar, GL_ARB_texture_env_dot3,
GL_ARB_texture_mirrored_repeat, GL_ARB_texture_non_power_of_two,
GL_ARB_texture_rectangle, GL_ARB_transpose_matrix, GL_ARB_vertex_program,
GL_ARB_window_pos, GL_EXT_abgr, GL_EXT_bgra, GL_EXT_blend_color,
GL_EXT_blend_equation_separate, GL_EXT_blend_func_separate,
GL_EXT_blend_logic_op, GL_EXT_blend_minmax, GL_EXT_blend_subtract,
GL_EXT_clip_volume_hint, GL_EXT_copy_texture, GL_EXT_draw_range_elements,
GL_EXT_fog_coord, GL_EXT_framebuffer_object, GL_EXT_multi_draw_arrays,
GL_EXT_packed_pixels, GL_EXT_paletted_texture, GL_EXT_point_parameters,
GL_EXT_polygon_offset, GL_EXT_rescale_normal, GL_EXT_secondary_color,
GL_EXT_separate_specular_color, GL_EXT_shadow_funcs,
GL_EXT_shared_texture_palette, GL_EXT_stencil_wrap, GL_EXT_subtexture,
GL_EXT_texture, GL_EXT_texture3D, GL_EXT_texture_edge_clamp,
GL_EXT_texture_env_add, GL_EXT_texture_env_combine,
GL_EXT_texture_env_dot3, GL_EXT_texture_lod_bias,
GL_EXT_texture_mirror_clamp, GL_EXT_texture_object,
GL_EXT_texture_rectangle, GL_EXT_vertex_array, GL_APPLE_packed_pixels,
GL_ATI_draw_buffers, GL_ATI_texture_env_combine3,
GL_ATI_texture_mirror_once, GL_ATIX_texture_env_combine3,
GL_IBM_texture_mirrored_repeat, GL_INGR_blend_func_separate,
GL_MESA_pack_invert, GL_MESA_ycbcr_texture, GL_NV_blend_square,
GL_NV_fragment_program, GL_NV_light_max_exponent, GL_NV_point_sprite,
GL_NV_texgen_reflection, GL_NV_texture_rectangle, GL_NV_vertex_program,
GL_NV_vertex_program1_1, GL_SGI_color_matrix, GL_SGI_color_table,
GL_SGIS_generate_mipmap, GL_SGIS_texture_border_clamp,
GL_SGIS_texture_edge_clamp, GL_SGIS_texture_lod, GL_SGIX_depth_texture,
GL_SGIX_shadow, GL_SGIX_shadow_ambient, GL_SUN_multi_draw_arrays

visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
----------------------------------------------------------------------
0x23 24 tc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
0x24 24 tc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 0 0 None
0x25 24 tc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x26 24 tc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x27 24 dc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
0x28 24 dc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 0 0 None
0x29 24 dc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x2a 24 dc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x5c 32 tc 0 32 0 r . . 8 8 8 8 0 0 0 0 0 0 0 0 0 Ncon

Die andere geeft dit:

glxgears
2042 frames in 5.0 seconds = 408.399 FPS
1916 frames in 5.0 seconds = 379.601 FPS
1540 frames in 5.0 seconds = 305.483 FPS
1560 frames in 5.0 seconds = 310.837 FPS
1560 frames in 5.0 seconds = 310.718 FPS
1538 frames in 5.0 seconds = 305.749 FPS
1560 frames in 5.1 seconds = 308.172 FPS
1560 frames in 5.1 seconds = 308.504 FPS
1560 frames in 5.0 seconds = 309.012 FPS
Gebruikersavatar
adri
Moderator
Berichten: 11541
Lid geworden op: 5 maart 2005, 14:00
Locatie: Diessen
    unknown unknown

Bericht door adri »

3-D versnelling is zo te zien wel ingeschakeld, anders haalde je niet zulke hoge cijfers bij glxgears.
Afbeelding
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

That's all you've got to say?

DDD.
Gebruikersavatar
adri
Moderator
Berichten: 11541
Lid geworden op: 5 maart 2005, 14:00
Locatie: Diessen
    unknown unknown

Bericht door adri »

Ik gebruik Compiz niet en kan er dus verder weinig over zeggen...
Wat voor output krijg je als je Compiz via de commandline opstart?
Afbeelding
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

Bedoel je dit?

richard@richard-desktop:~$ sudo compiz
[sudo] password for richard:
Checking for Xgl: not present.
Detected PCI ID for VGA: 01:00.0 0300: 1002:5960 (rev 01) (prog-if 00 [VGA controller])
Checking for texture_from_pixmap: present.
Checking for non power of two support: present.
Checking for Composite extension: present.
Comparing resolution (1280x1024) to maximum 3D texture size (2048): Passed.
Checking for nVidia: not present.
Checking for FBConfig: present.
Checking for Xgl: not present.
/usr/bin/compiz.real (core) - Fatal: No GLXFBConfig for default depth, this isn't going to work.
/usr/bin/compiz.real (core) - Error: Failed to manage screen: 0
/usr/bin/compiz.real (core) - Fatal: No manageable screens found on display :0.0
Gebruikersavatar
adri
Moderator
Berichten: 11541
Lid geworden op: 5 maart 2005, 14:00
Locatie: Diessen
    unknown unknown

Bericht door adri »

Liever niet als sudo (het moet zo ook werken).
Heb je misschien hier iets aan?

Start Compiz eens zo op: compiz --replace

Edit:
En hier nog eentje waar je wellicht baat bij hebt:
http://ubuntuforums.org/showthread.php?t=590775
Afbeelding
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

Compiz-replace geeft:

Checking for Xgl: not present.
Detected PCI ID for VGA: 01:00.0 0300: 1002:5960 (rev 01) (prog-if 00 [VGA controller])
Checking for texture_from_pixmap: present.
Checking for non power of two support: present.
Checking for Composite extension: present.
Comparing resolution (1280x1024) to maximum 3D texture size (2048): Passed.
Checking for nVidia: not present.
Checking for FBConfig: present.
Checking for Xgl: not present.
/usr/bin/compiz.real (core) - Fatal: No GLXFBConfig for default depth, this isn't going to work.
/usr/bin/compiz.real (core) - Error: Failed to manage screen: 0
/usr/bin/compiz.real (core) - Fatal: No manageable screens found on display :0.0


Hetzelfde dus..

De compiz check laat het volgende zien:

Gathering information about your system...

Distribution: Ubuntu 8.04
Desktop environment: GNOME
Graphics chip: ATI Technologies Inc RV280 [Radeon 9200 PRO] (rev 01)
Driver in use: radeon
Rendering method: AIGLX

Checking if it's possible to run Compiz on your system...

Checking for texture_from_pixmap... [ OK ]
Checking for non power of two support... [ OK ]
Checking for composite extension... [ OK ]
Checking for FBConfig... [ OK ]
Checking for hardware/setup problems... [ OK ]


Ook in orde..
Gebruikersavatar
Koen_92
Berichten: 758
Lid geworden op: 17 oktober 2006, 19:28
Locatie: Betuwe
    unknown unknown

Bericht door Koen_92 »

3D versnelling is niet ingeschakeld.
Verglijk jouw glxgears:

Code: Selecteer alles

2042 frames in 5.0 seconds = 408.399 FPS
1916 frames in 5.0 seconds = 379.601 FPS
1540 frames in 5.0 seconds = 305.483 FPS
1560 frames in 5.0 seconds = 310.837 FPS
1560 frames in 5.0 seconds = 310.718 FPS
1538 frames in 5.0 seconds = 305.749 FPS
1560 frames in 5.1 seconds = 308.172 FPS
1560 frames in 5.1 seconds = 308.504 FPS
1560 frames in 5.0 seconds = 309.012 FPS
maar eens met de mijne:

Code: Selecteer alles

24014 frames in 5.0 seconds = 4802.766 FPS
24680 frames in 5.0 seconds = 4935.974 FPS
24696 frames in 5.0 seconds = 4939.046 FPS
24770 frames in 5.0 seconds = 4953.931 FPS
Verder geeft glxinfo bij jouw deze regel terug:

Code: Selecteer alles

direct rendering: NO (If you want to find out why, try setting LIBGL_DEBUG=verbose)  
Daar moet natuurlijk 'yes' staan.
Probeer eens de 3D-driver op de 'ubuntu-manier' te installeren, dat gaat zo:
ga naar systeem --> beheer --> beperkt ondersteunde stuurprogramma's (of in het engels: restricted driver manager).
Kijk of je daar een driver aan kunt vinken, zo ja installeer die. Zo nee: typ in de terminal:
sudo lshw

en geef hier de output terug van dat commando.
Als je daar wel een driver kan installeren, moet je dat doen, en daarna je pc opnieuw opstarten. Vervolgens moet je weer glxgears en glxinfo draaien (en kijken of je nu meer fps terug krijgt, en of direc rendering 'yes' terug geeft)
adri schreef: 3-D versnelling is zo te zien wel ingeschakeld, anders haalde je niet zulke hoge cijfers bij glxgears.
is 400 fps hoog dan? Dat haal ik namelijk ook zonder 3d-versnelling. En ik heb ook al een oudere Pentium 4.... ;)
Gebruikersavatar
adri
Moderator
Berichten: 11541
Lid geworden op: 5 maart 2005, 14:00
Locatie: Diessen
    unknown unknown

Bericht door adri »

Op mijn oude P4 haal ik zo rond de 225, dus ik weet haast zeker dat hij 3-D versnelling heeft. :)
Op mijn nieuwere P4 scoor ik zo rond de 3500. :!:

Jij hebt gewoon een veel snellere kaart.

@Citroentje:
heb je die links die ik plaatste al bekeken?
Afbeelding
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

Hah, Koen.

Nou eh, die regel systeem->beheer->beperkt ondersteunde stuurprogramma's staat er al niet, het dichtst in de buurt komt nog hardware drivers en deze geeft een leeg veld...

Verder het resultaat van het commando sudo lshw:

description: Desktop Computer
product: K8N
vendor: ASUSTek Computer Inc.
version: To Be Filled By O.E.M.
serial: To Be Filled By O.E.M.
width: 32 bits
capabilities: smbios-2.3 dmi-2.3 smp-1.1 smp
configuration: boot=normal chassis=desktop cpus=1 uuid=8097F980-8DFE-D511-8141-0013D464D748
*-core
description: Motherboard
product: 'K8N'
vendor: ASUSTeK Computer INC.
physical id: 0
version: Rev 1.xx
serial: MB-1234567890
slot: Keyboard
*-firmware
description: BIOS
vendor: American Megatrends Inc.
physical id: 0
version: 1007.009 (07/01/2005)
size: 64KiB
capacity: 448KiB
capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb agp ls120boot zipboot biosbootspecification
*-cpu
description: CPU
product: AMD Sempron(tm) Processor 2800+
vendor: Advanced Micro Devices [AMD]
physical id: 4
bus info: cpu@0
version: 15.12.2
serial: To Be Filled By O.E.M.
slot: Socket 754
size: 1600MHz
capacity: 1600MHz
width: 64 bits
clock: 200MHz
capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt x86-64 3dnowext 3dnow up pni lahf_lm ts ttp tm stc
*-cache:0
description: L1 cache
physical id: 5
slot: L1-Cache
size: 128KiB
capabilities: pipeline-burst internal varies data
*-cache:1
description: L2 cache
physical id: 6
slot: L2-Cache
size: 256KiB
capacity: 256KiB
capabilities: pipeline-burst internal varies unified
*-cache:2 DISABLED
description: L3 cache
physical id: 7
slot: L3-Cache
capabilities: internal
*-memory
description: System Memory
physical id: 3a
slot: System board or motherboard
size: 512MiB
*-bank:0
description: DIMM [empty]
product: PartNum0
vendor: Manufacturer0
physical id: 0
serial: SerNum0
slot: DIMM0
*-bank:1
description: DIMM DDR Synchronous 400 MHz (2.5 ns)
product: PartNum1
vendor: Manufacturer1
physical id: 1
serial: SerNum1
slot: DIMM1
size: 512MiB
width: 64 bits
clock: 400MHz (2.5ns)
*-bank:2
description: DIMM [empty]
product: PartNum2
vendor: Manufacturer2
physical id: 2
serial: SerNum2
slot: DIMM2
*-pci:0
description: Host bridge
product: nForce3 250Gb Host Bridge
vendor: nVidia Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: a1
width: 32 bits
clock: 66MHz
*-isa
description: ISA bridge
product: nForce3 250Gb LPC Bridge
vendor: nVidia Corporation
physical id: 1
bus info: pci@0000:00:01.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: isa bus_master
configuration: latency=0
*-serial
description: SMBus
product: nForce 250Gb PCI System Management
vendor: nVidia Corporation
physical id: 1.1
bus info: pci@0000:00:01.1
version: a1
width: 32 bits
clock: 66MHz
capabilities: pm cap_list
configuration: driver=nForce2_smbus latency=0 maxlatency=1 mingnt=3 module=i2c_nforce2
*-usb:0
description: USB Controller
product: CK8S USB Controller
vendor: nVidia Corporation
physical id: 2
bus info: pci@0000:00:02.0
version: a1
width: 32 bits
clock: 66MHz
capabilities: pm ohci bus_master cap_list
configuration: driver=ohci_hcd latency=0 maxlatency=1 mingnt=3 module=ohci_hcd
*-usb:1
description: USB Controller
product: CK8S USB Controller
vendor: nVidia Corporation
physical id: 2.1
bus info: pci@0000:00:02.1
version: a1
width: 32 bits
clock: 66MHz
capabilities: pm ohci bus_master cap_list
configuration: driver=ohci_hcd latency=0 maxlatency=1 mingnt=3 module=ohci_hcd
*-usb:2
description: USB Controller
product: nForce3 EHCI USB 2.0 Controller
vendor: nVidia Corporation
physical id: 2.2
bus info: pci@0000:00:02.2
version: a2
width: 32 bits
clock: 66MHz
capabilities: debug pm ehci bus_master cap_list
configuration: driver=ehci_hcd latency=0 maxlatency=1 mingnt=3 module=ehci_hcd
*-bridge
description: Ethernet interface
product: CK8S Ethernet Controller
vendor: nVidia Corporation
physical id: 5
bus info: pci@0000:00:05.0
logical name: eth0
version: a2
serial: 00:13:d4:64:d7:48
size: 100000000
capacity: 100000000
width: 32 bits
clock: 66MHz
capabilities: bridge pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=forcedeth driverversion=0.61 duplex=full ip=10.0.0.150 latency=0 link=yes maxlatency=20 mingnt=1 module=forcedeth multicast=yes port=MII speed=100MB/s
*-multimedia
description: Multimedia audio controller
product: nForce3 250Gb AC'97 Audio Controller
vendor: nVidia Corporation
physical id: 6
bus info: pci@0000:00:06.0
version: a1
width: 32 bits
clock: 66MHz
capabilities: pm bus_master cap_list
configuration: driver=Intel ICH latency=0 maxlatency=5 mingnt=2 module=snd_intel8x0
*-ide:0
description: IDE interface
product: CK8S Parallel ATA Controller (v2.5)
vendor: nVidia Corporation
physical id: 8
bus info: pci@0000:00:08.0
logical name: scsi0
version: a2
width: 32 bits
clock: 66MHz
capabilities: ide pm bus_master cap_list emulated
configuration: driver=pata_amd latency=0 maxlatency=1 mingnt=3 module=pata_amd
*-cdrom
description: DVD writer
product: DVD_RW ND-3540A
vendor: _NEC
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/cdrom
logical name: /dev/dvd
logical name: /dev/scd0
logical name: /dev/sr0
version: 1.01
serial: [_NEC DVD_RW ND-3540A 1.0105031600
capabilities: removable audio cd-r cd-rw dvd dvd-r
configuration: ansiversion=5 status=open
*-ide:1
description: IDE interface
product: CK8S Serial ATA Controller (v2.5)
vendor: nVidia Corporation
physical id: a
bus info: pci@0000:00:0a.0
logical name: scsi3
version: a2
width: 32 bits
clock: 66MHz
capabilities: ide pm bus_master cap_list emulated
configuration: driver=sata_nv latency=0 maxlatency=1 mingnt=3 module=sata_nv
*-disk
description: ATA Disk
product: ST380817AS
vendor: Seagate
physical id: 0.0.0
bus info: scsi@3:0.0.0
logical name: /dev/sda
version: 3.42
serial: 4MR2SWT5
size: 74GiB (80GB)
capabilities: partitioned partitioned:dos
configuration: ansiversion=5 signature=e124e124
*-volume:0
description: Windows NTFS volume
physical id: 1
bus info: scsi@3:0.0.0,1
logical name: /dev/sda1
version: 3.1
serial: 1a16d21c-9c4b-134b-af92-d43bd88e6a31
size: 43GiB
capacity: 43GiB
capabilities: primary bootable ntfs initialized
configuration: clustersize=4096 created=2008-05-11 01:48:50 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true
*-volume:1
description: Extended partition
physical id: 2
bus info: scsi@3:0.0.0,2
logical name: /dev/sda2
size: 31GiB
capacity: 31GiB
capabilities: primary extended partitioned partitioned:extended
*-logicalvolume:0
description: Linux filesystem partition
physical id: 5
logical name: /dev/sda5
logical name: /
logical name: /dev/.static/dev
capacity: 29GiB
configuration: mount.fstype=ext3 mount.options=rw,relatime,errors=remount-ro,data=ordered state=mounted
*-logicalvolume:1
description: Linux swap / Solaris partition
physical id: 6
logical name: /dev/sda6
capacity: 1357MiB
capabilities: nofs
*-pci:0
description: PCI bridge
product: nForce3 250Gb AGP Host to PCI Bridge
vendor: nVidia Corporation
physical id: b
bus info: pci@0000:00:0b.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-display:0 UNCLAIMED
description: VGA compatible controller
product: RV280 [Radeon 9200 PRO]
vendor: ATI Technologies Inc
physical id: 0
bus info: pci@0000:01:00.0
version: 01
width: 32 bits
clock: 66MHz
capabilities: agp agp-3.0 pm vga_controller bus_master cap_list
configuration: latency=64 mingnt=8
*-display:1 UNCLAIMED
description: Display controller
product: RV280 [Radeon 9200 PRO] (Secondary)
vendor: ATI Technologies Inc
physical id: 0.1
bus info: pci@0000:01:00.1
version: 01
width: 32 bits
clock: 66MHz
capabilities: pm bus_master cap_list
configuration: latency=64 mingnt=8
*-pci:1
description: PCI bridge
product: nForce3 250Gb PCI-to-PCI Bridge
vendor: nVidia Corporation
physical id: e
bus info: pci@0000:00:0e.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-pci:1
description: Host bridge
product: K8 [Athlon64/Opteron] HyperTransport Technology Configuration
vendor: Advanced Micro Devices [AMD]
physical id: 101
bus info: pci@0000:00:18.0
version: 00
width: 32 bits
clock: 33MHz
*-pci:2
description: Host bridge
product: K8 [Athlon64/Opteron] Address Map
vendor: Advanced Micro Devices [AMD]
physical id: 102
bus info: pci@0000:00:18.1
version: 00
width: 32 bits
clock: 33MHz
*-pci:3
description: Host bridge
product: K8 [Athlon64/Opteron] DRAM Controller
vendor: Advanced Micro Devices [AMD]
physical id: 103
bus info: pci@0000:00:18.2
version: 00
width: 32 bits
clock: 33MHz
*-pci:4
description: Host bridge
product: K8 [Athlon64/Opteron] Miscellaneous Control
vendor: Advanced Micro Devices [AMD]
physical id: 104
bus info: pci@0000:00:18.3
version: 00
width: 32 bits
clock: 33MHz
configuration: driver=k8temp module=k8temp
Gebruikersavatar
Citroentje
Berichten: 1517
Lid geworden op: 9 februari 2007, 23:46
Locatie: Enschede
    unknown unknown

Bericht door Citroentje »

adri schreef:@Citroentje:
heb je die links die ik plaatste al bekeken?
Tuurlijk, Adri.

Die ene gaf mij de compiz-check waarvan het resultaat er staat en van die andere word ik niet echt veel wijzer, die mensen op dat forum ook niet volgens mij. :D
Plaats reactie